路由器设置过程中关于OSPF的network设置

网络 路由交换
OSPF是link state protocol,主要是interface状态(如ip address,mask,Hello time…)这些信息在Routers间建立adjency的过程中会通过LSAs被互换。

OSPF是link state protocol,主要是interface状态(如ip address,mask,Hello time…)这些信息在Routers间建立adjency的过程中会通过LSAs被互换,直到同Area收敛,所有Routers有同样的link state database,然后以自己为根(root)建立SPF tree,最后在根据SPF计算出route table.Area内任何一个interface的变化都会被Update.

我们再看看OSPF执行时的过程:(简单举例)

int s1

ip add 10.1.1.1 255.255.255.0 (10.1.1.1/24)

int s2

ip add 172.2.0.1 255.255.255.0 (172.2.0.1/24)

int s3

ip add 172.3.0.1 255.255.0.0 (172.3.0.1/16)

int s4

ip add 172.4.0.1 255.255.0.0 (172.4.0.1/16)

route ospf 10

network 10.1.1.1 0.0.0.0 area 0

network 172.2.0.0 0.0.255.255 area 0

当进入OSPF 10,OSPF首先执行network 10.1.1.1 0.0.0.0,查找interface address,有匹配s0,分配至Area 0,然后再执行network 172.2.0.0.0.0.255.255 aera 0,匹配s2->Area 0,最后我们在其它Routers上看到的信息是:

172.16.0.0/24 is subnetted, 1 subnets

O 172.16.0.0 [110/128] via 192.168.0.1, 00:00:00, Serialx

10.0.0.0/24 is subnetted, 1 subnets

O 10.1.1.0 [110/74] via 192.168.0.1, 00:00:05, Serialx

在着里可以看到submask是24,忽略了在network中配制的inverse mask,为什么?

我们再看当添加新的network后有什么结果?

route ospf 10

network 10.1.1.1 0.0.0.0 area 0

network 172.2.0.0 0.0.255.255 area 0

network 172.0.0.0 0.255.255.255 area 1

network 0.0.0.0 0.0.0.0 area 2

show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

Gateway of last resort is not set

O IA 172.3.0.0/16 [110/933] via 192.168.0.1, 00:00:05, Serialx

O IA 172.4.0.0/16 [110/933] via 192.168.0.1, 00:00:02, Serialx

172.16.0.0/24 is subnetted, 1 subnets

O 172.16.0.0 [110/128] via 192.168.0.1, 00:00:10, Serialx

10.0.0.0/24 is subnetted, 1 subnets

O 10.1.1.0 [110/74] via 192.168.0.1, 00:00:05, Serialx

这里s3,s4都在Area 1(被标记为IA掩码16)。

总结:实际的网络范围在interface mask中已经说明了,这在所有的Routers的Link state database 被清楚标记,不会因OSPF的network配置而发生改变。而在OSPF的network配置中,inverse mask只是起到指明在本Router的OSPF process 中的网络范围的作用,如network 172.0.0.0 0.255.255.255指定范围从172.0.0.0 ~ 172.255.255.255,在次范围中的所有interface分配至Area 1,最后其他所有的地址被分配到Area 2.

如果在Stub Area 中,没有Loopback interface的情况下,甚至可以简单配制为

router ospf 20

network 0.0.0.0 255.255.255.255 area x

这样就不用单独指定网络范围了。

在其它类型中,推荐配置使用interface ip address,0.0.0.0即精确匹配,以防止错误发生。如:

network 10.1.1.1 0.0.0.0 area 0

责任编辑:张存 来源: 中国it实验室
相关推荐

2009-12-16 10:08:07

2009-11-16 15:17:22

路由器设置

2011-08-29 18:30:05

华硕路由器路由器

2009-11-23 12:50:26

ADSL宽带路由器设置

2009-11-25 13:16:42

网吧路由器设置

2009-11-25 14:38:49

无线路由器

2011-08-11 13:49:24

2011-08-08 10:47:20

路由器宽带限速

2009-11-27 10:18:16

Cisco路由器手册

2009-11-26 13:50:16

无线路由器

2011-09-14 16:30:36

tp link路由器设路由器限速设置路由器

2009-12-01 16:46:10

2010-08-04 14:08:50

路由器设置

2009-12-03 10:18:46

路由器地址设置

2010-08-06 10:29:07

路由器设置

2011-09-02 10:56:09

netcore路由器设路由器

2011-08-29 13:04:09

路由器设置路由器连接路由器

2009-11-11 14:41:22

2009-12-03 09:13:38

网通路由器设置

2009-11-26 11:26:45

路由器设置局域网路由器设备
点赞
收藏

51CTO技术栈公众号