switch命令大全(1)

switch(enable) set password 

switch(enable) set enalbepass 

switch(config)# interface vlan 1 

switch(config-if)# ip address ip-address netmask 

switch(config-if)# ip default-gateway ip-address 

在基于CLI的交换机上设置远程访问: 

switch(enable) set interface sc0 ip-address netmask broadcast-address 

switch(enable) set interface sc0 vlan 

switch(enable) set ip route default gateway 

switch(config-if)# cdp enable 

switch(config-if)# no cdp enable 

为了查看Cisco邻接设备的CDP通告信息: 

switch# show cdp interface [type modle/port] 

switch# show cdp neighbors [type module/port] [detail] 

在基于CLI的交换机上启用和浏览CDP信息: 

switch(enable) set cdp {enable|disable} module/port 

为了查看Cisco邻接设备的CDP通告信息: 

switch(enable) show cdp neighbors[module/port] 

[vlan|duplex|capabilities|detail] 

switch(config-if)# description description-string 

基于CLI的交换机的端口描述: 

switch(enable)set port name module/number description-string 

switch(config-if)# speed{10|100|auto} 

在基于CLI的交换机上设置端口速度: 

switch(enable) set port speed moudle/number {10|100|auto} 

switch(enable) set port speed moudle/number {4|16|auto} 

switch(config-if)# duplex {auto|full|half} 

在基于CLI的交换机上设置以太网的链路模式: 

switch(enable) set port duplex module/number {full|half} 

switch# vlan database 

switch(vlan)# vlan vlan-num name vla 

switch(vlan)# exit 

switch# configure teriminal 

switch(config)# interface interface module/number 

switch(config-if)# switchport mode access 

switch(config-if)# switchport access vlan vlan-num 

switch(config-if)# end 

在基于CLI的交换机上配置静态VLAN: 

switch(enable) set vlan vlan-num [name name] 

switch(enable) set vlan vlan-num mod-num/port-list 

switch(config)# interface interface mod/port 

switch(config-if)# switchport mode trunk 

switch(config-if)# switchport trunk encapsulation {isl|dotlq} 

switch(config-if)# switchport trunk allowed vlan remove vlan-list 

switch(config-if)# switchport trunk allowed vlan add vlan-list 

在基于CLI的交换机上配置VLAN中继线: 

switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate] 

Vlan-range [isl|dotlq|dotl0|lane|negotiate] 

switch# vlan database 

switch(vlan)# vtp domain domain-name 

在基于CLI的交换机上配置VTP管理域: 

switch(enable) set vtp [domain domain-name] 

switch# vlan database 

switch(vlan)# vtp domain domain-name 

switch(vlan)# vtp {sever|cilent|transparent} 

switch(vlan)# vtp password password 

在基于CLI的交换机上配置VTP 模式: 

switch(enable) set vtp [domain domain-name] 

[mode{ sever|cilent|transparent }][password password] 

switch# vlan database 

switch(vlan)# vtp v2-mode 

在基于CLI的交换机上配置VTP版本: 

switch(enable) set vtp v2 enable 

switch# vlan database 

switch(vlan)# vtp pruning 

在基于CL I 的交换机上启动VTP剪裁: 

switch(enable) set vtp pruning enable 

switch(config-if)# port group group-number 

[distribution {source|destination}] 

在基于CLI的交换机上配置以太信道: 

switch(enable) set port channel moudle/port-range mode

{on|off|desirable|auto} 

switch(config-if)# spanning-tree [vlan vlan-list] cost cost 

在基于CLI的交换机上调整根路径成本: 

switch(enable) set spantree portcost moudle/port cost 

switch(enable) set spantree portvlancost moudle/port 

[cost cost][vlan-list] 

switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority 

在基于CLI的交换机上调整端口ID: 

switch(enable) set spantree portpri {mldule/port}priority 

switch(enable) set spantree portvlanpri {module/port}priority [vlans]  

switch(config)# spanning-tree [vlan vlan-list] hello-time seconds 

switch(config)# spanning-tree [vlan vlan-list] forward-time seconds 

switch(config)# spanning-tree [vlan vlan-list] max-age seconds 

在基于CLI的交换机上修改STP时钟: 

switch(enable) set spantree hello interval[vlan] 

switch(enable) set spantree fwddelay delay [vlan] 

switch(enable) set spantree maxage agingtiame[vlan] 

switch(config-if)#spanning-tree portfast 

在基于CLI的交换机端口上启用或禁用Port Fast 特征: 

switch(enable) set spantree portfast {module/port}{enable|disable} 

switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second] 

在基于CLI的交换机端口上启用或禁用UplinkFast 特征: 

switch(enable) set spantree uplinkfast {enable|disable}

[rate update-rate] [all-protocols off|on] 

ATM (config)# interface atm number.subint multioint 

ATM(config-subif)# lane serber-bus ethernet elan-name 

ATM(config)# lane database database-name 

ATM(lane-config-databade)# name elan1-name server-atm-address 

les1-nsap-address 

ATM(lane-config-databade)# name elan2-name server-atm-address 

les2-nsap-address 

ATM(lane-config-databade)# name … 

ATM(config)# interface atm number 

ATM(config-if)# lane config database database-name 

ATM(config-if)# lane config auto-config-atm-address 

ATM(config)# interface atm number.subint multipoint 

ATM(config)# lane client ethernet vlan-num elan-num 

router# configure terminal 

router(config)# interface media module/port 

router(config-if)# description description-string 

router(config-if)# ip address ip-addr subnet-mask 

router(config-if)# no shutdown 

router(config)# interface module/port.subinterface 

router(config-ig)# encapsulation[isl|dotlq] vlan-number 

router(config-if)# ip address ip-address subnet-mask

router(config)# interface atm module/port 

router(config-if)# no ip address 

router(config-if)# atm pvc 1 0 5 qsaal 

router(config-if)# atm pvc 2 0 16 ilni 

router(config-if)# interface atm module/port.subinterface multipoint 

router(config-if)# ip address ip-address subnet-mask 

router(config-if)# lane client ethernet elan-num 

router(config-if)# interface atm module/port.subinterface multipoint 

router(config-if)# ip address ip-address subnet-name 

router(config-if)# lane client ethernet elan-name 

router(config-if)# …