IPX 访问控制列表

    R2#conft
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#access-1 801 deny 12
R2(config)#access-S 801 permit -1
R2(config)#int s0
R2(config-if)#ipx access-group 801 out
R2(config-if)#^Z
R2#
R2#sh ipx access-S
IPX standard access list 801
　deay 12
　permit FFFFFFFF
R2#sh ipx int s0
Serial0 is up, line date interval is 60 seconds
　IPX type 20 propagation packet forwarding is disabled
　Outgoing access list is 801
　IPX helper access list is not set
　... (输出省略)
R2#
Term_Server#1
[Resuming connection 1 to r1...]
R1#ping ipx AA.0000.0c31.a81b
Type escape sequence to abort.
Sending 5,100-byte IPX Novell 
Echoes to AA.0000.0c31,a81b,timeout is 2 seconds:
.....
Success rate is 0 percent(0/5)
R1#conft
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#int e0
R1(config-if)#ipx netw 102
R1(config-if)#
Term_Server#2
[Resuming connection 2 to r2 ... ]
R2#conft
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#int e0
R2(config-if)#ipx netw 102
R2(config-if)#^Z
R2#
Term_Server#1
[Resuming connection 1 to r1 ... ]
R1#
11:42:23: %SYS-5-CONFIG_I: Configured from console by console
Ripping ipx AA.0000.0c31.a81b
Type escape sequence to abort.
Sending 5,100-byte IPX Novell 
Echoes to AA.0000.0c31.a81b,timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), 
round-trip min/avg/max =32/33/40 ms
R1#

    R2#conft
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#access-1 901 permit any 102 AA
R2(config)#access-1 901 deny any any
R2(config)#int s0
R2(config-if)#ipx access-1 901 out
R2(config-if)#^Z
R2#sh ipx access-1
IPX standard access list 801
　deny 12
　permit FFFFFFFF
IPX extended access list 901
　permit any 102 AA
　deny any any
R2#sh ipx int s0
Serial0 is up, line protocol is up
　IPX address is 23.0000.0c8e.cdd2 [up]
　Delay of this IPX network, in ticks is 6 throughput 0 link delay 0
　IPXWAN processing not enabled on this interface.
　IPX SAP update interval is 60 seconds
　IPX type 20 propagation packet forwarding is disabled
　Incoming access list not set
　Outgoing access list is 901
　IPX helper access list is not set
　SAP GGS output filter list is not set

    R2#conft
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#ipx access-list standard Test3
R2(config"ipx-std-nacl)#deny 12
R2(config-ipx-std-nacl)#permit -1
R2(config-ipx-std-nacl)#exit
R2(config)#ipx access-list extended Test4
R2(config-ipx-ext-nacl)#permit any 102 AA
R2(config-ipx-ext-nacl)#deny any any
R2(config-ipx-ext-nacl)#^Z
R2#
R2#sh ipx access-1
IPX standard ajccess list 801
　deny 12
　permit FFFFFFFF
IPX extended access l